OpenWrt

Topic: New Broadcom BCM63xx codebase with GPL'd Ethernet and USB support Message: Ok I managed to find a old phone data cable which worked well. I don't have the necessary components to connect it properly however holding the cables in place allowed ... [More] me to get the output from cfe. Here is a full copy of the boot log from the serial console : http://pastebin.com/m5002cf7c [Less]

Topic: New Broadcom BCM63xx codebase with GPL'd Ethernet and USB support Message: Isaac702 wrote:Here is a image of the board. http://img207.imageshack.us/img207/4452/dscn5211x.jpgI'm not sure if this would be much help in identifying the port.I am ... [More] right in assuming the 4 pin connect in the left center of the image is a serial port. Behind that connector there is the code "J303".If it is then I can try to get the necessary equipment to access the console. I think yes, J303 is serial console with 3'3v level outputs, you must identify TX,RX, and GND pins. Also you must use a TTL to RS232 conversor. (3'3 -> +/-12V). As you can see there is unpopulated capacitors C306-C307-C308, not indispensable.I see also connectors:J201 -> JTAG with unpopulated components RP201 (i think 10 ohms)andJ301 -> USB Host?J304 -> USB Slave? with unpopulated capacitors and resistors below.luck [Less]

Topic: New Broadcom BCM63xx codebase with GPL'd Ethernet and USB support Message: Here is a image of the board. http://img207.imageshack.us/img207/4452/dscn5211x.jpgI'm not sure if this would be much help in identifying the port.I am right in ... [More] assuming the 4 pin connect in the left center of the image is a serial port. Behind that connector there is the code "J303".If it is then I can try to get the necessary equipment to access the console. [Less]

Topic: New Broadcom BCM63xx codebase with GPL'd Ethernet and USB support Message: t3l3m4k0 wrote:Isaac702 wrote:Here is a copy of the output for the "dmesg" command. http://pastebin.com/f1787aec I try to find inside your dmesg, name of your board, i ... [More] can't.Do you have a serial port in your router?If yes, try to connect at 115200 bps, 8 bits, no parity and capture cfe (broadcom bootloader) boot messages to see name of your board.thnx I presumed that the name of the board was V2110 due to it being listed in the official firmware for the device and in the output of cpuinfo. (http://pastebin.com/f61041c0d).There appears to be a four pin connector on the board however I have no experience in this area and do not know if it is a serial port. [Less]

Topic: New Broadcom BCM63xx codebase with GPL'd Ethernet and USB support Message: Isaac702 wrote:Here is a copy of the output for the "dmesg" command. http://pastebin.com/f1787aec I try to find inside your dmesg, name of your board, i can't.Do you ... [More] have a serial port in your router?If yes, try to connect at 115200 bps, 8 bits, no parity and capture cfe (broadcom bootloader) boot messages to see name of your board.thnx [Less]

Topic: New Broadcom BCM63xx codebase with GPL'd Ethernet and USB support Message: t3l3m4k0 wrote:Isaac702 wrote:t3l3m4k0 wrote:@Isaac702you must patch file: root/trunk/target/linux/brcm63xx/files/arch/mips/bcm63xx/boards/board_bcm963xx.cwith ... [More] apropiate values of your board at this points: I had done this already however just in case I check it again. The boardid is V2110 and the cpu is a 6348.When I try to update it returns the error "The firmware update is failed. The selected file contains an illegal image."I have checked other firmwares and cannot see any other firmware with the variables in the positions I stated above. The exception to this is the RTA1025 which is the board the BT Voyager 2110 is based upon.I will retract the statement saying the problem is with the firmware version as there is a version 1 device supported by OpenWRT.Editied: To remove quoted code. can you post "dmesg" command result, from original firmware? Here is a copy of the output for the "dmesg" command. http://pastebin.com/f1787aec [Less]

Topic: New Broadcom BCM63xx codebase with GPL'd Ethernet and USB support Message: ma_jk wrote:Ive got a flash issue with a BMC6358 board.Flash memory starts from 0x1f80 0000, but bootstrap is set from 0x1fc0 0000.I can flash the firmware from that ... [More] location and it works fine. Only problem is that i loose 4 entire MB!How do i solve this? Shouldnt rootfs automatically create a split fs? Should i add a partition manually? at this moment you must add this manually or create a patch/profile for your router at:root/trunk/tools/firmware-utils/src/imagetag.csalut [Less]

Topic: New Broadcom BCM63xx codebase with GPL'd Ethernet and USB support Message: Isaac702 wrote:t3l3m4k0 wrote:@Isaac702you must patch file: root/trunk/target/linux/brcm63xx/files/arch/mips/bcm63xx/boards/board_bcm963xx.cwith apropiate values of ... [More] your board at this points: I had done this already however just in case I check it again. The boardid is V2110 and the cpu is a 6348.When I try to update it returns the error "The firmware update is failed. The selected file contains an illegal image."I have checked other firmwares and cannot see any other firmware with the variables in the positions I stated above. The exception to this is the RTA1025 which is the board the BT Voyager 2110 is based upon.I will retract the statement saying the problem is with the firmware version as there is a version 1 device supported by OpenWRT.Editied: To remove quoted code. can you post "dmesg" command result, from original firmware? [Less]

Topic: New Broadcom BCM63xx codebase with GPL'd Ethernet and USB support Message: t3l3m4k0 wrote:@Isaac702you must patch file: root/trunk/target/linux/brcm63xx/files/arch/mips/bcm63xx/boards/board_bcm963xx.cwith apropiate values of your board at ... [More] this points: I had done this already however just in case I check it again. The boardid is V2110 and the cpu is a 6348.When I try to update it returns the error "The firmware update is failed. The selected file contains an illegal image."I have checked other firmwares and cannot see any other firmware with the variables in the positions I stated above. The exception to this is the RTA1025 which is the board the BT Voyager 2110 is based upon.I will retract the statement saying the problem is with the firmware version as there is a version 1 device supported by OpenWRT.Editied: To remove quoted code. [Less]

Topic: New Broadcom BCM63xx codebase with GPL'd Ethernet and USB support Message: Ive got a flash issue with a BMC6358 board.Flash memory starts from 0x1f80 0000, but bootstrap is set from 0x1fc0 0000.I can flash the firmware from that location and ... [More] it works fine. Only problem is that i loose 4 entire MB!How do i solve this? Shouldnt rootfs automatically create a split fs? Should i add a partition manually? [Less]