W

W-Bus communication package

Settings | Report Duplicate

0

I Use This!

Inactive

Commits : Listings

Analyzed about 1 hour ago. based on code collected about 1 hour ago.

Commit Message	Contributor	Files Modified	Lines Added	Lines Removed	Code Location	Date
Jul 29, 2024 — Jul 29, 2025 Showing page 1 of 12 Search / Filter on:
fix undefined GSM reset interval and heaterMode	mjander	More...				over 11 years ago
separate heater mode setting from start heater menu functions. Correct dead lock (cant turn heater on again) in case heater is not connected.	mjander	More...				over 11 years ago
fix beep frequency	mjander	More...				over 11 years ago
Some bug fixes for openegg: Correct timer clock (was running too fast). Make key press autorepeat faster. Fix GSM flash area corruption.	mjander	More...				over 11 years ago
Add K-line hardware info, so that people hopefuly stop asking again and again the same stuff.	mjander	More...				over 11 years ago
Use different linker section for settings to avoid conflict with GSM.	mjander	More...				over 11 years ago
Add sanity check to parser to avoid potential memory corruption	mjander	More...				over 11 years ago
Assume some defaults for CAF, PSENSOR and NOZZLE since most people wont care about those anyway.	mjander	More...				over 11 years ago
fix compile problems.	mjander	More...				over 11 years ago
some fix forgotten to check in and I already do not remember what it does fix.	mjander	More...				over 11 years ago
Fix CAF inconsistency. Enable CP during ignition, this prevents overheating during restart when the water in the heat exchanger is still quite hot.	mjander	More...				over 12 years ago
Sensor thresholds.	mjander	More...				over 12 years ago
Apply feedback from field tests. Add script to plot Data Top data logs.	mjander	More...				over 12 years ago
Make voltage measurement more accurate by considering polarity protection diode voltage drop.	mjander	More...				almost 13 years ago
Parametrize make for different hardware variants of heater device. Status: Hago + Toy CAF setup works, Delavan + DBW46 CAF does not.	mjander	More...				almost 13 years ago
Adjust partial load CAF.	mjander	More...				almost 13 years ago
Tune Full load. Still some black smoke during start.	mjander	More...				almost 13 years ago
Partial load running OK. Full load needs new tuning of parameters.	mjander	More...				almost 13 years ago
Fix (untestet) electrical switch on/off through second w-bus line. Adapt CAF settings, correct scale of Heating Power value, currently used for compressor pressure in centibar.	mjander	More...				almost 13 years ago
Working parameters for cheap CAF and Hago .2 nozzle.	mjander	More...				almost 13 years ago
Enable dosing pump cold thick oil problem preheating during glow sequence. Some small CAF changes.	mjander	More...				almost 13 years ago
Add cold thick oil dosing pump preheating work around.	mjander	More...				almost 13 years ago
Fix compilation (missing include) for Linux 3.4.7.	mjander	More...				almost 13 years ago
First working data set for part load / full load switching. Not optimal, but operational.	mjander	More...				about 13 years ago
Add toy blower scale factor to adapt the air flow mass. Tune CAF PID parameters again since previous values where flawed due to problems with the optical reflection RPM sensor (doubled pulses at low RPM).	mjander	More...				over 13 years ago
Working version, start rather suboptimal (smoke).	mjander	More...				over 13 years ago
Parametrize full load and partial load values.	mjander	More...				over 13 years ago
Fix overflow on msp430 of sequencer values. Deactivate GK and FPW modulation.	mjander	More...				over 13 years ago
Work in progress.	mjander	More...				over 13 years ago
Adapt CAF values to RPM domain (was RPS).	mjander	More...				over 13 years ago

←
1
2
3
4
5
6
7
8
9
10
11
12
→